MED260923CS!002ENGD- -  -  N- HERMETIC -N- S- S- -20/07/2023- Marine Equipment- - SN- S- - N-  - 1,203,751B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED260923CS/002- N-Jul 19, 20281203751
 
Form
  Marine Equipment(TO)
Certification N. MED260923CS/002 - (ENG)
Certificate date 20/07/2023
Type Protezione antincendio
Product Penetrations through "A" Class divisions: (b) pipe, duct, trunk, etc. penetrations
Item Nº MED/3.26b
USCG Category N° 164.138

Model or Denomin.
Items
HERMETIC
Applicant CHIBRO Srl Società con socio unico
Place of requester Via Valtellina, 15  %  22070 Montano Lucino (CO)  % ITALY
Tel. N.,Fax, Email 0314781800, ---, pcrescini@rubinetteriebresciane.it
Directive (EU) 2022/1157
Standards IMO Res. MSC.307(88)-(2010 FTP Code) - IMO MSC.1/Circ. 1488
Reference Documents Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 07/07/2023
Expire date 19/07/2028
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED260923CS/002

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2022/1157.
MED Item Nº MED/3.26b
USCG Category Nº 164.138
Description Penetrations through "A" Class divisions: (b) pipe, duct, trunk, etc. penetrations
Type HERMETIC
Applicant CHIBRO Srl Società con socio unico
Via Valtellina, 15,22070 Montano Lucino (CO),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code) - IMO MSC.1/Circ. 1488
Reference standards Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
July 20, 2023
July 19, 2028
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED260923CS/002
Page 1 of 4





Product description


Transits of metallic pipes having diameter ranging from 6 up to 273 mm through bulkheads and decks.
The transits consist of nodular cast iron casings screwed to stainless steel flanges or aluminium casings screwed to aluminium flanges, fitted with one EPDM gasket and one layer of intumescing material. The pipes and the transits are insulated, when required and on the side shown in the drawings, with mineral wool having density of 100 kg/m3 and/or insulating material named MICROBIFIRE. The mineral wool consists of cylinders (certified non combustible in conformity to the requirements of the IMO FTP Code) 30, 40 and 70 mm thick and mineral wool shaped panels (certified non combustible in conformity to the requirements of the IMO FTP Code) having thickness ranging from 25 up to 70 mm. The MICROBIFIRE material, whose density is 300 kg/m3 and thickness 15 mm, may be applied in one or two layers. On the side exposed to the fire of the decks the insulating material applied on the pipes is to be fixed, when shown in the drawings, by means of steel wire net.

















 



ATTACHMENT TO
CERTIFICATE Nr. MED260923CS/002
Page 2 of 4


Field of application

Fire resistant A Class pipe transits through decks and bulkheads having Class as described in the following tables:



Notes for bulkheads (not for aluminium):
  • the transit having diameter of 219 mm may be considered as transit having Class A60, if insulated with mineral wool having thickness of 70 mm and length of 500 mm both on exposed and unexposed side; the side not exposed is to be fitted, for a length of 200 mm, with a further layer of mineral wool having thickness of 50 mm;
  • the transit having diameter of 6 mm may be considered as transit having Class A0 and A60 if, respectively, uninsulated, or if insulated with mineral wool having thickness of 70 mm and length of 100 mm both on exposed and unexposed side.










 



ATTACHMENT TO
CERTIFICATE Nr. MED260923CS/002
Page 3 of 4



Reference documents

CHIBRO SpA drawings No. 2.39.189.300 (57 sheets) dated 5 June 2008, No. 2.39.189.320 (39 sheets) dated July 2009, No. 2.39.189.400 (50 sheets) dated May 2009, No. 2.39.189.600 dated 6 April 2009 (61 sheets), No. 2.39.189.660 (74 sheets) No. 2.39.189.699 and No. 2.39.189.698 approved respectively with endorsement No. LABS-155 on 22 July 2008, No. LABS-236 on 17 March 2009, No. LABS-280 on 4 June 2009, No. LABS- 351 on 17 September 2009, No. LABS-358, No. LABS-359 and No. LABS-360 on 16 October 2009.
CHIBRO Spa drawings enclosed to LAPI Test report N. 1073.4IM0150/09 dated 2 October 2009.


Tests carried out

Tests as per RINA Test Laboratory Reports No. 2008CS012001 dated 22 July 2008, No. 2008CS014752 dated 30 March 2009, No. 2009CS011893 dated 4 June 2009, No. 2009CS012436 dated 17 September 2009 and No. 2009CS013911 dated 19 October 2009 issued according to IMO Resolution A. 754(18) A.IV.
LAPI Test report N. 1073.4IM0150/09 issued on 2 October 2009 according to IMO Resolution A. 754(18).




ATTACHMENT TO
CERTIFICATE No. MED260923CS/002
Pages 4 of 4
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****