MED285122CSENGB- -  -  N- PORTELLO A PARATIA -N- S- S- -07/07/2022- Marine Equipment- - SN- S- - N-  - 326,763B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità- MED285122CS- N-Jul 6, 2027326763
 
Form
  Marine Equipment(TO)
MED285122CS
Certification N. MED285122CS - (ENG)
Certificate date 07/07/2022
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16

Model or Denomin.
Items
PORTELLO A PARATIA
Applicant FINCANTIERI S.P.A.
Place of requester VIA GENOVA 1  %  34121 Trieste (TS)  % ITALY
Tel. N.,Fax, Email 040 3193111, 040 3192305, stefano.weiss@fincantieri.it
Directive (EU) 2021/1158
Standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference Documents Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 28/6/2022
Expire date 06/07/2027
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED285122CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2021/1158.
MED Item Nº MED/3.16
Description Fire doors
Type PORTELLO A PARATIA
Applicant FINCANTIERI S.P.A.
VIA GENOVA 1,34121 Trieste (TS),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference standards Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
July 7, 2022
July 6, 2027
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED285122CS
Page 1 of 2

Product description

Single leaf hinged vertical door with the following maximum dimensions
  • LSS Version: clear opening 6510x2006 (WxH) mm - leaf 6590x2080 (WxH) mm
The leaf, having thickness of 218 mm, is composed of one steel plate, 8 mm thick and the insulating material, at sight, composed of two layers of mineral wool having thickness of 50 and 30 mm and density of 100 kg/m3 named ROCKWOOL SEAROX SL 620. The leaf is fitted with vertical bulbs stiffeners, having height of 140 mm and thickness of 8 mm, welded to the steel plate with pitch ranging from 600 up to 1000 mm and an horizontal steel plate, 8 mm thick, and having height of 100 mm fitted at height of 1165 mm. The stiffener are insulated, on the upper side by means of one layer of the same mineral wool having thickness of 30 mm. The leaf is fitted with an hinge, in the middle of the upper side, and with a lever closing device, fitted on the side not exposed to the fire, that acts on eight points. The mineral wool is fixed to the steel plate and to the stiffenersl by means of steel pins and washers welded with pitch of 200 mm on steel plate and 300 mm on the stiffeners. The door frame is composed of a steel profile, 5 mm thick and having dimensions of 50x50 mm welded to a steel plate having minimum thickness of 8 mm and is insulated by means of two layers of the same mineral wool having thickness of 50 e 30 mm.
Field of application
Fire resistant A-30 Class single leaf hinged vertical door with fire hazard on side fitted with the hinges.
Reference documents
Goriziane SpA drawings No. 22702-D01-150-00 Rev. C and No. 22702-D01-100-00 Rev. B dated 8/11/2017, No. 22717-D01-150-00 Rev. 0 dated 1/8/2017 and No. 22717-D01-100-00 Rev. 0 dated 11/8/2017 approved on 15/12/2017 respectively with endorsement Nos. LABS-1580, LABS-1581, LABS-1582 and LABS-1583.
Tests carried out
Test as per RINA Test Laboratory report No. 2017CS011627/1 issued on 15 December 2017 according to IMO 2010 FTP CODE. Increased dimensions verified with Technical Report No. 2017/011/TCHU dated December 2017.




ATTACHMENT TO
CERTIFICATE No. MED285122CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****