MED010723CSENGD- -  -  N- MAPFLEX® -N- S- S- -21/03/2023- Marine Equipment- - SN- S- - N-  - 1,194,552B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità- MED010723CS- N-Mar 20, 20281194552
 
Form
  Marine Equipment(TO)
MED061523MI/007
Certification N. MED010723CS - (ENG)
Certificate date 21/03/2023
Type Protezione antincendio
Product Surface materials and floor coverings with low flame-spread characteristics: (a) decorative veneers
Item Nº MED/3.18a
USCG Category N° 164.112

Model or Denomin.
Items
MAPFLEX®
Applicant MAP SPA
Place of requester VIA C. COLOMBO, 15  %  24046 Osio Sotto (BG)  % ITALY
Tel. N.,Fax, Email 0354195201, 0354825528, abergamini@mapspa.com
Directive (EU) 2022/1157
Standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference Documents Chap. II-2 and X of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 14/02/2023
Expire date 20/03/2028
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED010723CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2022/1157.
MED Item Nº MED/3.18a
USCG Category Nº 164.112
Description Surface materials and floor coverings with low flame-spread characteristics: (a) decorative veneers
Type MAPFLEX®
Applicant MAP SPA
VIA C. COLOMBO, 15,24046 Osio Sotto (BG),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference standards Chap. II-2 and X of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
March 21, 2023
March 20, 2028
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED010723CS
Page 1 of 3

Product description


Type 1 “Mapflex”:
Acoustic insulating material composed of plastic polymers and mineral fillers.

· Density (kg/m3) 2000 ± 10%
· Mass per area range (g/m2) 2000 ± 20%; 3000 ÷ 10000 ± 10%
· Thickness range (mm) 1 ± 20%; 1.5 ÷ 5 ± 10%

Type 2 “Mapflex” with nonwoven:
Acoustic insulating material composed of plastic polymers and mineral fillers featuring nonwoven on the exposed side.

· Density (kg/m3) 2000 ± 10%
· Mass per area range (g/m2) 2000 ± 20%; 3000 ÷ 10000 ± 10%
· Thickness range (mm) 1 ± 20%; 1.5 ÷ 5 ± 10%
Colour: white.
Field of application
Type 1 “Mapflex”:
As finishing material for all exposed interior and concealed or inaccessible surfaces (decorative veneer)
The product may be applied to any non-combustible (non metallic) support having density ³ 27 kg/m3.
Where applied to the whole surface of bulkhead and ceiling thickness is limited to 4 mm.
On the basis of the value of the total heat release (Qt) and on the basis of the value of the peak heat release (qp) the material is deemed not generating excessive quantities of smoke nor toxic products in fire according to Annex 2 IMO 2010 FTP Code.

Type 2 “Mapflex” with nonwoven:
As finishing material for all exposed interior and concealed or inaccessible surfaces (decorative veneer).
The product may be applied to any non-combustible (non metallic) support having density ³ 18 kg/m3.
Where applied to the whole surface of bulkhead and ceiling thickness is limited to 3.4 mm.
On the basis of the value of the total heat release (Qt) and on the basis of the value of the peak heat release (qp) the material is deemed not generating excessive quantities of smoke nor toxic products in fire according to Annex 2 IMO 2010 FTP Code.


 



ATTACHMENT TO
CERTIFICATE Nr. MED010723CS
Page 2 of 3

Tests carried out

Type 1 “Maplex”:
Tests as per RINA Test Laboratory report No. 2007CS015841/11 issued on 14 April 2008 report No. 2009CS014298 issued on 4 November 2009 according to:
· IMO Res. A.653(16);
· ISO 1716: 1973.
Tests as per RINA test Laboratory reports No. 2013CS013150/2 dated 30 October 2013, Nos. 2013CS013150/2 and /3 dated 7 November 2013 and No. 2023CS01107/3 dated 21 March 2023 according to:
· IMO 2010 FTP Code Part 5;
· ISO 1716: 2010.

Type 2 “Mapflex” with nonwoven:
Tests as per RINA test Laboratory reports No. 2023CS01107/1, /2 and /4 dated 21 March 2023 issued according to:
· IMO 2010 FTP Code Part 5;
· ISO 1716: 2010.




ATTACHMENT TO
CERTIFICATE No. MED010723CS
Pages 3 of 3
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****