ELE154425XGENG- -  -  N- AA-10411 Series -N- S- S- -05/05/2026- Prodotti Elettrici- - SN- N- Giuseppe Russo- N-  - 2,334,709Giuseppe RussoBbisProdotti ElettriciNumero Pratica,NumDich,Norma,NumBusta,Richiesta,Validità- ELE154425XG- N-May 4, 20312334709
 
Form
  Prodotti Elettrici(TO)
Certification N. ELE154425XG - (ENG)
Certificate date 05/05/2026
Type Impianti Elettrici
Product INTERRUTTORI AUTOMATICI

Model or Denomin.
Items
AA-10411 Series
Applicant Astrol Electronic AG
Place of requester Ahornweg,14  %  5504 Othmarsingen  % SWITZERLAND
Tel. N.,Fax, Email ---, ---, ---
Standards IEC 60947-2
Expire date 04/05/2031
Head Office HAMBURG
Interrut.senza Dettaglio ENG
Vuoto Querysave
S
TYPE APPROVAL CERTIFICATE
No. ELE154425XG
This is to certify that the product below is found to be in compliance with the applicable requirement of the RINA type approval system.

Description CIRCUIT BREAKERS
Type AA-10411 Series
Applicant Astrol Electronic AG
Ahornweg,14
5504 Othmarsingen
SWITZERLAND
Reference standards IEC 60947-2
  

 
 
   .   This Certificate is valid until May 4, 2031
_________________________________
RINA Services S.p.A.
Giuseppe Russo
This certificate consists of this page and 1 enclosure
**** NOTICE: This is NOT an official certificate ****

TYPE APPROVAL CERTIFICATE
No. ELE154425XG
Enclosure - Page 1 of 2
AA-10411 Series
Components
  • DC Circuit breakers / DC-bus tie device
Model Types:
Ident number
Description
Nominal current
Size
No. Modules
AA-10411-101
DC-Breaker 0.5 kA - 1.5 kV
500 A
smal
1
AA-10411-111
DC-Breaker 0.35 kA - 1.5 kV
350 A
small
1
AA-10411-102
DC-Breaker 1.25 kA - 1.5 kV
1250 A
medium
1
AA-10411-112
DC-Breaker 1.1 kA - 1.5 kV
1100 A
medium
1
AA-10411-122
DC-Breaker 1.5 kA - 1.5 kV
1500 A
medium
1
AA-10411-103
DC-Breaker 3.0 kA - 1.5 kV
3000 A
large
2
AA-10411-113
DC-Breaker 2.25 kA - 1.5 kV
2250 A
large
2

.
General Specification
Parameter
Min
Max
Unit
Notes
DC Link voltage 0.01 1500
V

DC Link nominal current 0.35 3.0
kA

System loop inductance
100
µH
1
Breaking time
10
µs
3
Breaking current
20
kA
3
Clearance time
625
µs
2, 3
24 V Power 16 100
W

Link Length
30
m
6
Ambient temperature 5 60
°C

Water inlet temperature
49
°C
4
Humidity
95 %
RH
5
IP grade electronic
IP54

IP grade switch
IP54

Notes:
1. System inductance is not limiting factor but does have influence on overvoltage protection
2. Depends on customer system (inductance, voltage, current)
3. Refer to Astrol "Manual Marine DC-Breaker" doc.No. AD-10811-020 rev. 2.7
4. Tap water or deionized water is applicable
5. Non-condensing
6. Any optical link


Software Package
FPGA FW
CPU Appliation
MU4HV FW
GDU FW
CU4FAN Fw
DC-Breaker
1.46
2.1
1.07
1.0
1.04





TYPE APPROVAL CERTIFICATE
No. ELE154425XG
Enclosure - Page 2 of 2
AA-10411 Series

Other Conditions
The DC Breaker is a (bi-) directional fault current suppressor based on current interruption by switching of insulated gate bipolar transistors (IGBT).
The device is used for fault current suppression and does not replace circuit breakers or switches for isolation.
The system design need to be approved on a case-by-case basis, and must include, as part of the overall system arrangement:
- means for manual, local, operation independent of higher-level automation system, enabling necessary means for local operation, local/remote change over, and interface for setting of parameters
- means for monitoring and indication of operating status and alarms
- back-up protection (e.g. fuses) in accordance with relevant rule requirements (if applicable)
- documentation






HAMBURG May 5, 2026
**** NOTICE: This is NOT an official certificate ****