MED454924CSENG- -  -  N- HSF A60 -N- S- S- -22/01/2025- Marine Equipment- - SN- S- - N-  - 1,075,374B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED454924CS- N-Jan 21, 20301075374
 
Form
  Marine Equipment(TO)
Certification N. MED454924CS - (ENG)
Certificate date 22/01/2025
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model or Denomin.
Items
HSF A60
Applicant CARETTA SYSTEMS SA
Place of requester THESI PRARI MOUSTAKI  %  19300 Aspropyrgos  % GREECE
Tel. N.,Fax, Email 302105573694, ---, INFO@CARETTA-SYSTEMS.COM
Directive (EU) 2024/1975
Standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ.1319
Reference Documents SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511
Request 20/01/2025
Expire date 21/01/2030
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED454924CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2024/1975.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type HSF A60
Applicant CARETTA SYSTEMS SA
THESI PRARI MOUSTAKI,19300 Aspropyrgos,GREECE
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ.1319
Reference standards SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511
Issued in Genoa on
This Certificate is valid until
January 22, 2025
January 21, 2030
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED454924CS
Page 1 of 2

Product description

Single leaf hinged door, installed in an aluminium bulkhead, whose maximum clear opening dimensions are 1079 mm (W) and 2075 mm (H). The leaf, having maximum width of 1100 mm and maximum height of 2100 mm, is made of one single panel of a composite material. The panel is composed of three skins of material named CARETTA SHEET, 2 mm thick each and having nominal density of 1250 kg/m3 and, in between, two layers of mineral wool type ROCKWOOL SEAROX SL440, 22 mm thick and having nominal density of 150 kg/m3. Vertical stiffeners made of CARETTA SHEET are fitted, between the two skins, every 100 mm. The composite panel edge is contained within two U profiles: the outer steel profile has dimensions of 22x52x1 mm and the inner stainless steel profile has dimensions of 40x46x1.5 mm. The door is fitted with a locking system with lock type BMH DIN 18250, three concealed hinges type Simonswerk Tectus A8 3D, a concealed door closer type Dorma ITS 96.
The door frame is composed of steel profiles having thickness of 3 mm, fixed to the bulkhead by means of L-shaped profiles 40x40x4 mm and bolts type M8x25 with pitch of 150 mm. The door frame is fitted with rubber seal type Elastosil R 401/70 and strips of intumescent gaskets type Flexpan 200 10x1.5 mm.
Field of application
Fire resistant A-60 Class single leaf hinged door with the fire hazard on both sides in compliance with IMO MSC.1/Circ. 1319 dated 11 June 2009. In this case the dimensions relevant to the height and width of the door may be increased of 15% provided that the surface area is not increased of more than 10%.

In case of doors in compliance to the "Agreement between the European Community and the United States of America", the present certificate is valid at the following conditions:
- maximum door size tested;
- door used with a fire tested frame design.

The surfaces of this division may be fitted with products having low flame spread characteristics, installed as described in the relevant type approval certificates and satisfying the requirements of SOLAS 74 Reg. II-2 as applicable.
Reference documents
CARETTA SYSTEMS SA drawing No. HSF-A60-180 Rev. A dated 16 January 2025 enclosed to RINA Test Laboratory Report No. 2024CS014549/1.
Tests carried out
Tests as per RINA Test Laboratory report No. 2024CS014549/1 issued on 22 January 2025 according to IMO 2010 FTP Code Part 3.




ATTACHMENT TO
CERTIFICATE No. MED454924CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****