MED213323CS!004ENGD- -  -  N- UTECHGTA  -N- S- S- -08/11/2023- Marine Equipment- - SN- S- - N-  - 528,096B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED213323CS/004- N-Nov 7, 2028528096
 
Form
  Marine Equipment(TO)
MED009524NA/004
Certification N. MED213323CS/004 - (ENG)
Certificate date 08/11/2023
Type Protezione antincendio
Product Surface materials and floor coverings with low flame-spread characteristics: (a) decorative veneers
Item Nº MED/3.18a
USCG Category N° 164.112

Model or Denomin.
Items
UTECHGTA
Applicant TEKNOWOOL SUD S.R.L.
Place of requester VIA FERRANTE IMPARATO 109  %  80146 Napoli (NA)  % ITALY
Tel. N.,Fax, Email 081 5593222, 081 7528284, infosud@teknowool.com
Directive (EU) 2023/1667
Standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference Documents Chap. II-2 and X of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 30/07/2023
Expire date 07/11/2028
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED213323CS/004

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2023/1667.
MED Item Nº MED/3.18a
USCG Category Nº 164.112
Description Surface materials and floor coverings with low flame-spread characteristics: (a) decorative veneers
Type UTECHGTA
Applicant TEKNOWOOL SUD S.R.L.
VIA FERRANTE IMPARATO 109,80146 Napoli (NA),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference standards Chap. II-2 and X of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
November 8, 2023
November 7, 2028
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED213323CS/004
Page 1 of 2





Product description

Mineral wool cupel with a density of 60 Kg/m3, covered on one side with fiberglass fabric
430 g/m2 +/- 5% thickness 0.36 mm primed, glued with 20 g/m2 of adhesive.

Declared wool density (kg/m3) 60 +/- 10%

Declared thickness (mm) 20 +/- 5%

Fields of application

As finishing material for all exposed interior and concealed or inaccessible surfaces (decorative veneer).
The product may be applied to any metallic and non-combustible support if the product would not need any adhesive or combustible material layer.
On the basis of the value of the total heat release (Qt) and on the basis of the value of the peak heat release (qp) the material is deemed not generating excessive quantities of smoke nor toxic products in fire according to Annex 2 IMO 2010 FTP Code.
In case of use on surfaces and linings as specified in paragraph 3.2.1 of SOLAS 1974 Chapter II-2 Reg. 5, where the calorific value shall not exceed 45 MJ/m2 for the thickness used as required in paragraph 3.2.2, the use of the certified product must be evaluated.

Tests carried out

Tests as per RINA Test Laboratory reports No. 2023CS012243/8 dated 08 November 2023 issued according to:
  • IMO 2010 FTP Code Part 5




ATTACHMENT TO
CERTIFICATE No. MED213323CS/004
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****