MED327125CSENGB- -  -  N- PORTA A PARATIA -N- S- S- -02/07/2025- Marine Equipment- - SN- S- - N-  - 251,429B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED327125CS- N-Jul 1, 2030251429
 
Form
  Marine Equipment(TO)
MED327125CS
Certification N. MED327125CS - (ENG)
Certificate date 02/07/2025
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model
Items/Sizes
PORTA A PARATIA
Applicant AL.MA.RI.NA. SOC. COOP. P.A.
Place of requester LOCALITA' GRETI DI DURASCA 10-12  %  19020 Follo (SP)  % ITALY
Tel. N.,Fax, Email 0187 558548, --- , andreasassarini@almarina.it
Directive (EU) 2024/1975
Standard IMO Res. MSC.307(88)-(2010 FTP Code) - IMO MSC.1/Circ. 1319
Reference Documents SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511
Request 26/06/2025
Validity 01/07/2030
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED327125CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2024/1975.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type PORTA A PARATIA
Applicant AL.MA.RI.NA. SOC. COOP. P.A.
LOCALITA' GRETI DI DURASCA 10-12,19020 Follo (SP),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code) - IMO MSC.1/Circ. 1319
Reference standards SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511
Issued in Genoa on
This Certificate is valid until
July 2, 2025
July 1, 2030
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED327125CS
Page 1 of 2

Product description

Double leaf hinged door whose maximum clear opening size is 1880 x 1200 mm. The leaves, having thickness of 153 mm, maximum height of 1933 mm and maximum width of 633 and 725 mm, are composed of a 20 mm thick steel plate and a 4 mm thick steel plate fitted on the opposite side. The internal insulating material is composed of two layers of mineral wool (certified non-combustible in conformity to the requirements of the IMO FTP Code) 30 mm thick each and having density of 100 kg/m3 and a cavity, in between. Inside each leaf, five L shaped stiffeners (four horizontal and one vertical) having dimensions of 50x50x5 mm, are welded to the steel plate having thickness of 20 mm. On the rabbet between leaf and frame a gasket having dimensions of 40x25 mm and an intumescent strip type PROMASEAL L, are fitted. Inside each leaf a lever closing device, that acts on 6 points and actuated by an handle, is fitted. The door frame is composed of a steel plate having thickness of 20 mm, coplanar with the leaf plate and butt welded to the bulkhead, and two L shaped steel profiles that make the rabbet.
Field of application
Fire resistant A-60 Class single leaf hinged door, intended for general applications.
In case of doors in compliance to the "Agreement between the European Community and the United States of America", the present certificate is valid at the following conditions:
- door used with a fire tested frame design
Reference documents
Al.Ma.Ri.Na. drawing No. ALM-2401-B-004 dated 30 July 2013 and approved on 29 August 2013 with endorsement No. LABS-814.
Tests carried out
Test as per RINA Test Laboratory report No. 2012CS013383/2 issued on 30 August 2013 according to Appendix 1 of IMO 2010 FTP Code Part 3.




ATTACHMENT TO
CERTIFICATE No. MED327125CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****