MED373926CSENGF- -  -  N- Fire resistant B-15 class single leaf hinged door  -N- S- S- -22/06/2026- Marine Equipment- - SN- S- - N-  - 244,549B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED373926CS- N-Jun 21, 2031244549
 
Form
  Marine Equipment(TO)
Certification N. MED373926CS - (ENG)
Certificate date 22/06/2026
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model or Denomin.
Items
Fire resistant B-15 class single leaf hinged door
Applicant NAVAL SUPPLIERS SRL Unipersonale
Place of requester ZONA INDUSTRIALE 24  %  33049 San Pietro Al Natisone (UD)  % ITALY
Tel. N.,Fax, Email +39 0432 727860, +39 0432 727886, firedoors@navalsuppliers.com
Directive (EU) 2025/1533
Standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ.1319
Reference Documents SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511/Rev.1
Request 19/06/2026
Expire date 21/06/2031
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED373926CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2025/1533.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type Fire resistant B-15 class single leaf hinged door
Applicant NAVAL SUPPLIERS SRL Unipersonale
ZONA INDUSTRIALE 24,33049 San Pietro Al Natisone (UD),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ.1319
Reference standards SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511/Rev.1
Issued in Genoa on
This Certificate is valid until
June 22, 2026
June 21, 2031
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED373926CS
Page 1 of 2

Product description

Single leaf hinged door whose maximum clear opening size is 1100 (W) x 2100 (H) mm. The door leaf, having maximum dimensions of 1128 (W) x 2108 (H) mm, is composed of two carbon steel sheets 1.2 mm thick each and, in between, one mineral wool layer (certified non combustible in conformity to the IMO FTP Code), 35 mm thick and having density of 115 kg/m3. The leaf is fitted, on the perimeter, with C shaped carbon steel profiles, 1.2 mm thick and having dimensions of 40x15 mm. Inside the leaf, in the central part, No. 2 longitudinal C shaped carbon steel stiffeners, 1 mm thick and having dimensions of 40x12 mm, are welded to the steel sheets on the upper and lower part of the leaf. The door frame and the sill are composed of an hollow carbon steel profile having thickness of 1.2 mm.
Field of application
Fire resistant B-15 Class single leaf hinged door in compliance with IMO MSC.1/Circ. 1319 dated 11 June 2009. In this case the dimensions relevant to the height and with of the door may be increased of 15% provided that the surface area is not increased of more than 10%.

In case of doors in compliance to the "Agreement between the European Community and the United States of America", the present certificate is valid at the following conditions:
- maximum door size tested;
- door used with a fire tested frame design.

The surfaces of this division may be fitted with products having low flame spread characteristics, installed as described in the relevant type approval certificates and satisfying the requirements of SOLAS 74 Reg. II-2 as applicable.
Reference documents
Naval Suppliers drawing No. FT_PTB1_2111_R00 dated 17 June 2011 approved on 30 June 2011 with endorsement No. LABS-565.
Tests carried out
Tests as per RINA Test Laboratory Report No. 2011CS012201/1 issued on 1 July 2011 according to IMO Res. A. 754(18) and to IMO MSC.1/Circ. 1319 dated 11 June 2009.




ATTACHMENT TO
CERTIFICATE No. MED373926CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****