“Aquatech ®” is a manually/automatically operated water mist system consisting of nozzles, stainless steel piping, section valves, filters and control system. The system may be powered by costant pressure pump(s) or pressurized gas cylinders based on an accumulator unit (one nitrogen cylinder and one water cylinder):Pre-engineered systems requirements
Main component | Nitrogen (N2) (propellent) | Water (extinguishing agent) |
Cylinder volume | 27L. | 40L. |
Nominal pressure | 200 bar. | 200 bar. |
Pumps, pipes, valves, couplings and other systems components are subject to case by case approval.Nozzle characteristics
- Material: brass OT58.
- Spray and steaming: radial 360°.
- Discharge angle: 60°. - Functioning: pop-up.- Mist: from 50 to 150 micron.
- Filter: interchangeable stainless steel filter.- Test pressure: 150 bar.
- Working pressure: 100 bar.
- Flow rate: 6,5 lt/min.Fields of application
Local protection for deep fat fryers.
Nozzle installation requirements
Supply system | Pump(s) | Pre-engineered |
Projection | Downward. | Downward. |
Maximum cooking area protected by a
single nozzle | Single vat: 0.286 m².Double vat: 0.253 m² (both). | Single vat: 450 mm x 450 mm x 250 mm (h). Max 3 vat protected (1 nozzle per vat). |
Maximum distance from the fryer surface | 1380 mm. | 1380 mm. |
Minimum distance from the fryer surface | 900 mm. | 900 mm. |
K factor | 0.65. | 0.65. |
Minimum working pressure | 100 bar. | 200 bar decreasing |
Distribution line | To be verified case by
case. | D.12; stainless steel. Maximum length: 20m from the twin fluid valve. |
 | ATTACHMENT TO
CERTIFICATE No. MED109025CS
Page 2 of 3 |
Reference documents
- Nozzle datasheet, issued by by Tema Sistemi S.p.A. and filed by RINA with n° CSST-19771.
- Design, installation, operation and maintenance manual "MANUALE DI USO E INSTALLAZIONE SISTEMA DI SPEGNIMENTO AD ALTA PRESSIONE CON UGELLI TS-WMC56", dwg n° TS-MAN-WMC56 issued by Tema Sistemi S.p.A. and filed by RINA with n° CSST-19772.
- PRE-ENGINEERED TECHNICAL DESCRIPTION issued by Tema Sistemi S.p.A. and filed by RINA with n° CSST-24231.
- Sprayhead TS-WMC56, dwg n° TS031- Rev 1, issued by Tema Sistemi S.p.A. and approved by RINA with n° CSST-19774.
- Test report n° TS-WM/CM/01/19 issued by Brand Technology S.r.l. for Tema Sistemi S.p.A and filed by Rina with n° CSST-19890.
- Test report n° TS-WMF56-01/24 issued by Brand Technology S.r.l. for Tema Sistemi S.p.A and filed by Rina with n° CSST-24232.
Remarks
a) Installation of the system, spacing of nozzles and components used shall be in accordance with the type approval documentation;
b) Prior to fitting the system on board, the following details shall be submitted for approval for each installation:
- Ducts layout and nozzles arrangement;
- Schematic arrangement of the system including sizes and material of piping and method of pipe jointing, nozzle types;
- Specification of the pump unit or cylinder for pre-engineered system;
- Hydraulic calculation (excluding pre-engineered system);
c) The nozzles shall be marked with the name of the producer and the type designation as indicated in this certificate.