MED390624CS!003ENGB- -  -  N- ANKER A60 HST -N- S- S- -20/12/2024- Marine Equipment- - SN- S- - N-  - 194,862B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED390624CS/003- N-Dec 19, 2029194862
 
Form
  Marine Equipment(TO)
MED390624CS/003
Certification N. MED390624CS/003 - (ENG)
Certificate date 20/12/2024
Type Protezione antincendio
Product 'A' & 'B' class fire proof windows and side scuttles
Item Nº MED/3.25

Model or Denomin.
Items
ANKER A60 HST
Applicant HET ANKER BV
Place of requester KAATSBAAN 10  %  4209 Schelluinen  % NETHERLANDS
Tel. N.,Fax, Email +31183623135, ---, truus@anker-windows.com
Directive (EU) 2024/1975
Standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference Documents SOLAS 74 Reg. II-2/9,IMO Res. MSC.5(48)-(IGC Code) 3,IMO MSC/Circ.1120
Request 03/09/2024
Expire date 19/12/2029
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED390624CS/003

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2024/1975.
MED Item Nº MED/3.25
Description 'A' & 'B' class fire proof windows and side scuttles
Type ANKER A60 HST
Applicant HET ANKER BV
KAATSBAAN 10,4209 Schelluinen,NETHERLANDS
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference standards SOLAS 74 Reg. II-2/9; IMO Res. MSC.5(48)-(IGC Code) 3; IMO MSC/Circ.1120
Issued in Genoa on
This Certificate is valid until
December 20, 2024
December 19, 2029
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED390624CS/003
Page 1 of 2

Product description

Window composed of a composite pane having maximum clear opening size of 1460 mm in width and 2200 mm in height. The frame is composed of a carbon steel welded profile (10 and 12 mm thick) and a stainless steel glass retaining frame (30 x 5 mm) screwed to the profile; a layer of material named PROMATECT H, 20 mm thick and having width of 40 mm is fitted between the glass retaining frame and a stainless steel flat (40 x 3 mm) screwed to the frame. The glass pane compound, having minimum total thickness of 45 mm, is composed of a pane named CONTRAFLAM MARINE A60/N2 having total thickness of 27 mm (manufacturer Vetrotech) composed of four glasses, 4 and 5 mm thick and, in between, three layers of intumescing gel, an air gap 10 mm thick and a toughened glass having thickness of 8 mm named SECURIT PLANILUX (manufacturer Vetrotech). A ceramic fibre gasket having thickness of 3 mm, is fitted between the glass faces, the steel frame and glass retaining frame. Spacers, having dimensions of 20 x 50 mm and thickness of 4 mm, named PROMATECT H, are fitted between the glass lower edge and the steel frame.

Field of application
Fire resistant A60 Class window with fire hazard on the side fitted with the pane having thickness of 27 mm and in the inner side of the application.
Hose stream resistant.


Reference documents
Het Anker BV drawing No. FTW-SQ60op-1522-00 dated 6 December 2010 approved with endorsement No. LAB-521 on 18 January 2011.
Tests carried out
Tests as per RINA Test Laboratory report No. 2010CS015105/1 dated 18 January 2010.




ATTACHMENT TO
CERTIFICATE No. MED390624CS/003
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****