MED511525CS!033ENG- -  -  N- 316A60_1_#1660_0 -N- S- S- -29/12/2025- Marine Equipment- - SN- S- - N-  - 2,372,775B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED511525CS/033- N-Dec 28, 20302372775
 
Form
  Marine Equipment(TO)
Certification N. MED511525CS/033 - (ENG)
Certificate date 29/12/2025
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16

Model or Denomin.
Items
316A60_1_#1660_0
Applicant MARINE INTERIORS S.P.A.
Place of requester VIA GENOVA 1  %  34121 Trieste (TS)  % ITALY
Tel. N.,Fax, Email ---, ---, marco.varriale@fincantieri.it
Directive (EU) 2025/1533
Standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ. 1319
Reference Documents SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511/Rev.1
Request 15/01/2021
Expire date 28/12/2030
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED511525CS/033

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2025/1533.
MED Item Nº MED/3.16
Description Fire doors
Type 316A60_1_#1660_0
Applicant MARINE INTERIORS S.P.A.
VIA GENOVA 1,34121 Trieste (TS),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ. 1319
Reference standards SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511/Rev.1
Issued in Genoa on
This Certificate is valid until
December 29, 2025
December 28, 2030
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED511525CS/033
Page 1 of 3

Product description


Glazed single leaf hinged door with maximum clear opening of 1054x2200 mm (WxH) and leaf having maximum dimensions of 1226x2242 mm (WxH). The glass pane, having clear opening size of 1056x2087 mm is composed, moving from the unexposed side, of a grey temperated float having thickness of 19,5 mm, a void space 14 mm deep, a low emission tempered float having thickness of 6 mm, a void space 14 mm deep and a glass type CONTRAFLAM (manufacturer Vetrotech) having thickness of 27 mm. The frame of the door and the frame of the glazed door leaf are composed of hollow stainless steel profiles having thickness variable from 5 up to 12 mm, covered by an aluminium alloy cover 1.2 mm thick.
The frame of the door is bolted, by means of M10 screws, to a steel flat having dimensions of 125x25 mm (lower side) and to L shaped carbon steel profiles having dimensions of 150x100 mm (other sides) welded to the bulkhead. Between aluminium external profiles and stainless steel core, the frames are insulated by means of layers of calcium silicate type Promatect H (density of 870 kg/m3), while between leaves frame and glass pane a layer of ceramic fiber (certified non combustible in conformity to the requirements of the IMO FTP Code) having density of 70 kg/m3 is fitted.
Between door frame and L profile a ceramic fiber cord stiffened inconel is fitted while on the rabbet between frame and leaf a intumescent strip type Roku Strip having dimensions of 20x1.5 mm is positioned. The leaf is fitted with a closing devices that acts on three points actuated by the handle and equipped of three hinges. The door is fitted, on the unexposed side, with external active door closer.






















 



ATTACHMENT TO
CERTIFICATE Nr. MED511525CS/033
Page 2 of 3



Field of application
Fire resistant A-60 single leaf hinged door with fire hazard in the side opposite to the opening and fitted with the glass type CONTRAFLAM A60. Door in compliance with IMO MSC.1/Circ. 1319 dated 11 June 2009. In this case the width of the door may be increased of 15% provided that the surface area is not increased of more than 10%.


Reference documents
METALSIGMA TUNESI drawing No. 1478-3 T002 Rev. B dated 26 January 2021 approved on 2 February 2021 with endorsement No. LABS-2167.


Tests carried out

Tests as per RINA Test Laboratory Report No. 2019CS012477/2 issued on 06 February 2020 according to IMO 2010 FTP Code Part 3 and to IMO MSC.1/Circ. 1319 dated 11 June 2009.




ATTACHMENT TO
CERTIFICATE No. MED511525CS/033
Pages 3 of 3
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****