MED296826CS!001ENG- -  -  N- Wall Max Pipe Penetration - WR series - WR EX Series -N- S- S- -14/07/2026- Marine Equipment- - SN- S- - N-  - 396,753B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED296826CS/001- N-Jul 13, 2031396753
 
Form
  Marine Equipment(TO)
Certification N. MED296826CS/001 - (ENG)
Certificate date 14/07/2026
Type Protezione antincendio
Product Penetrations through "A" Class divisions: (b) pipe, duct, trunk, etc. penetrations
Item Nº MED/3.26b
USCG Category N° 164.138

Model or Denomin.
Items
Wall Max Pipe Penetration -  WR series - WR EX Series
Applicant WALLMAX SRL
Place of requester CORSO DI PORTA NUOVA 22  %  20121 MILANO  % ITALY
Tel. N.,Fax, Email 02 2171 1156, 02 93650825, ---
Directive (EU) 2025/1533
Standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ. 1488
Reference Documents SOLAS 74 Reg. II-2/9,IMO Res. MSC.1/Circ.1276/Rev.1,IMO Res. MSC.1/Circ.1655
Request 12/05/2026
Expire date 13/07/2031
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
No. MED296826CS/001

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2025/1533.
MED Item Nº MED/3.26b
USCG Category Nº 164.138
Description Penetrations through "A" Class divisions: (b) pipe, duct, trunk, etc. penetrations
Type Wall Max Pipe Penetration -  WR series - WR EX Series
Applicant WALLMAX SRL
CORSO DI PORTA NUOVA 22,20121 MILANO,ITALY
Testing standards applied IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ. 1488
Regulations specified and reference documents SOLAS 74 Reg. II-2/9; IMO Res. MSC.1/Circ.1276/Rev.1; IMO Res. MSC.1/Circ.1655
Issued in Genoa on
This Certificate is valid until
July 14, 2026
July 13, 2031
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
No.  MED296826CS/001
Page 1 of 3

Product description




Penetration of metallic pipe having diameter ranging from 10 mm up to 114 mm installed in A-Class steel bulkheads and decks. These transits are composed of EPDM cylindrical body modules, stainless steel discs on the extremities and screws for the expander mechanism, fitted inside a circular steel coaming welded in the middle, on both sides, to the deck or bulkhead plate. The transits are insulated, on both sides, with three layers of mineral wool type SeaRox SL 620, having density of 100 kg/m3 and thickness of 30 mm (first layer fitted around the transit) and 60 mm each (the other two layers); the mineral wool panels, having dimensions ranging from 240x240 mm up to 380x380 mm, are fixed to the bulkhead or deck plate by means of steel pins and washers welded with pitch ranging from 150 up to 200 mm.
















 



ATTACHMENT TO
CERTIFICATE Nr. MED296826CS/001
Page 2 of 3
Field of application
Fire resistant metallic pipes penetrations through steel bulkheads and decks as per following tables:

DECKS
Transit type
pipe type
Minimum diameter (mm)
Maximum diameter (mm)
Class
WR / WR Ex
steel
12
114
A-60
WR / WR Ex
copper
108
108
A-30

BULKHEADS
Transit type
pipe type
Minimum diameter (mm)
Maximum diameter (mm)
Class
WR / WR Ex
steel
10
114
A-60


Reference documents
WallMax drawing No. WDVpc16A60SBHA01 Rev. 1 and No. WDVpc16A60SDA01 Rev. 1 dated 16 December 2016 approved on 19 January 2017 respectively with endorsement Nos. LABS-1396 and LABS-1397. "Declaration of product identity" by WallMax Srl dated 14/07/2026.
Tests carried out
Tests as per RINA Test Laboratory Reports No. 2016CS01481/5 and No. 2016CS01481/6 issued on 19 January 2017 according to Appendix 1 of IMO 2010 FTPC Part 3 - A.III Pipe and Duct Penetrations.




ATTACHMENT TO
No. MED296826CS/001
Pages 3 of 3
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****