MED511525CS!029ENGB- -  -  N- 316A-0_2_#0600_01 -N- S- S- -29/12/2025- Marine Equipment- - SN- S- - N-  - 2,372,775B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED511525CS/029- N-Dec 28, 20302372775
 
Form
  Marine Equipment(TO)
MED511525CS/029
Certification N. MED511525CS/029 - (ENG)
Certificate date 29/12/2025
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16

Model or Denomin.
Items
316A-0_2_#0600_01
Applicant MARINE INTERIORS S.P.A.
Place of requester VIA GENOVA 1  %  34121 Trieste (TS)  % ITALY
Tel. N.,Fax, Email ---, ---, marco.varriale@fincantieri.it
Directive (EU) 2025/1533
Standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ.1319
Reference Documents SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511/Rev.1
Expire date 28/12/2030
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
No. MED511525CS/029

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2025/1533.
MED Item Nº MED/3.16
Description Fire doors
Type 316A-0_2_#0600_01
Applicant MARINE INTERIORS S.P.A.
VIA GENOVA 1,34121 Trieste (TS),ITALY
Testing standards applied IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ.1319
Regulations specified and reference documents SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511/Rev.1
Issued in Genoa on
This Certificate is valid until
December 29, 2025
December 28, 2030
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
No.  MED511525CS/029
Page 1 of 2

Product description

Glazed single leaf hinged door adjacent to a fixed glazed panel. The leaf has maximum dimensions of 820x2010 mm (WxH) and maximum clear opening of 752x1950 mm (WxH). The glass panes, having maximum clear opening size of 640x1830 mm (door) and 792x1950 mm (fixed panel), are composed, moving from the side opposite to the hinges, of a toughened glass type FLOAT CHIARO (manufacturer Vetrotech) having thickness of 6 mm, a PVB layer, 0.76 mm thick and a glass type PYROSWISS N.G. (manufacturer Vetrotech) having thickness of 8 mm. The door frames, the glass and the glazed panel, are composed of hollow stainless steel profiles having thickness of 1.5 mm, type Forster, bolted by means of M10 screws, on the side opposite to the hinges, to a steel flat having dimensions of 60x8 mm (lower side) and to L shaped carbon steel profiles having dimensions of 100x65x9 mm (other sides). The glass retaining frame, fitted on the side opposite to the hinges, is composed of hollow stainless steel profiles, having dimensions of 20x20 mm and thickness of 2 mm, screwed to the frame by means of M6 screws. Between the glass faces, the frame and the glass retaining frames, gaskets of KERAFIX FLEXLIT type, are fitted. Between the glass edges and the frame, spacers of calcium silicate type Firesil having width of 80 mm and thickness of 8 mm, are fitted. The door is fitted with external door closer.
Field of application
Fire resistant A-0 Class single leaf hinged door with fire hazard in the side opposite to the opening in compliance with IMO MSC.1/Circ. 1319 dated 11 June 2009. In this case the dimensions relevant to the height and width of the door may be increased of 15% provided that the surface area is not increased of more than 10%.
Reference documents
Metalsigma Tunesi drawing No. 1073-1 dated 5 November 2014 approved on 12 November 2014 with endorsement No. LABS-985.
Tests carried out
Tests as per RINA Test Laboratory Report No. 2014CS012492/1 issued on 12 November 2014 according to IMO 2010 FTP CODE and to IMO MSC.1/Circ. 1319 dated 11 June 2009.




ATTACHMENT TO
No. MED511525CS/029
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****