MED092922CS!001ENGF- -  -  N- PANNELLO CARRFAR-01 ALPHA METALLIC -N- S- S- -08/03/2022- Marine Equipment- - SN- S- - N-  - 1,015,517B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED092922CS/001- N-Feb 4, 20271015517
 
Form
  Marine Equipment(TO)
MED116122TS/001
Certification N. MED092922CS/001 - (ENG)
Certificate date 08/03/2022
Type Protezione antincendio
Product Surface materials and floor coverings with low flame-spread characteristics: (b) paint systems
Item Nº MED/3.18b

Model
Items/Sizes
PANNELLO CARRFAR-01 ALPHA METALLIC
Applicant CarrFAR SRL
Place of requester VIA PIETRAFERRATA N. 2  %  34148 Trieste (TS)  % ITALY
Tel. N.,Fax, Email 040 814297, 040814297, carrfarsrl@gmail.com
Directive (EU) 2021/1158
Standard IMO Res. MSC.307(88)-(2010 FTP Code)
Reference Documents Chap. II-2 and X of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 08/03/2022
Validity 04/02/2027
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
No. MED092922CS/001

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2021/1158.
MED Item Nº MED/3.18b
Description Surface materials and floor coverings with low flame-spread characteristics: (b) paint systems
Type PANNELLO CARRFAR-01 ALPHA METALLIC
Applicant CarrFAR SRL
VIA PIETRAFERRATA N. 2,34148 Trieste (TS),ITALY
Testing standards applied IMO Res. MSC.307(88)-(2010 FTP Code)
Regulations specified and reference documents Chap. II-2 and X of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
March 8, 2022
February 4, 2027
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
No.  MED092922CS/001
Page 1 of 2

Product description

Painting system composed of 3 layers:
1st layer: Water-based pigmented primer based of emulsion resin named “ALPHA BL GROUND” (manufacturer Akzo Nobel) - (mass per area: 137 g/m²);
2nd layer: decorative wall hydro-paint for interiors with metallized appearance, based on acrylic resin named “ALPHA METALLIC” (manufacturer Akzo Nobel) - (mass per area: 130 g/m², thickness: from 0.060 up to 0.070 mm);
3rd layer: satined water-based acrylic enamel for interior named “RUBBOL BL SATIN” (manufacturer Akzo Nobel) - (mass per area: 126 g/m², thickness: from 0.025 up to 0.030mm).
  • Mass per area (g/m2): 393 ± 10%
  • Thickness (mm): 0.125 ± 10%

Field of application
As finishing material for all exposed interior and concealed or inaccessible surfaces. The product may be applied to any non combustible support having thickness ³ 13 mm and density ³ 742 kg/m3

On the basis of the value of the total heat release (Qt) and on the basis of the value of the peak heat release (qp) the material is deemed not generating excessive quantities of smoke nor toxic products in fire according to Annex 2 IMO 2010 FTP Code.

Tests carried out
Tests as per LAPI Test Laboratory reports No. 016.4IM0100/12 and No. 016.4IM0090/12 dated 23 January 2012 issued according to:
  • IMO Res. A. 653(16);
  • ISO 1716: 1973.




ATTACHMENT TO
No. MED092922CS/001
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****