MED188325CSENGB- -  -  N- B15 BLIND HINGED DOOR 2 LEAVES - B15DHB2 -N- S- S- -11/04/2025- Marine Equipment- - SN- S- - N-  - 597,421B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED188325CS- N-Apr 10, 2030597421
 
Form
  Marine Equipment(TO)
MED188325CS
Certification N. MED188325CS - (ENG)
Certificate date 11/04/2025
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model
Items/Sizes
B15 BLIND HINGED DOOR 2 LEAVES - B15DHB2
Applicant BLU BUD SRL
Place of requester VIA CORSICA 21/20  %  16128 Genova (GE)  % ITALY
Tel. N.,Fax, Email 0108601379, 0108183053, info@blubud.it
Directive (EU) 2024/1975
Standard IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference Documents IMO MSC.1/Circ. 1319,SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511
Request 09/04/2025
Validity 10/04/2030
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED188325CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2024/1975.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type B15 BLIND HINGED DOOR 2 LEAVES - B15DHB2
Applicant BLU BUD SRL
VIA CORSICA 21/20,16128 Genova (GE),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference standards IMO MSC.1/Circ. 1319; SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511
Issued in Genoa on
This Certificate is valid until
April 11, 2025
April 10, 2030
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED188325CS
Page 1 of 2

Product description

Double leaf hinged door with maximum clear opening size of 2200 x 2100 mm (WxH). The leaves, having, each, dimensions of 1112x2110 mm (WxH) contain a glass compound, type PYROBEL 16 EI 30 (manufacturer AGC), having dimensions of 310x310 mm and total thickness of 17.3 m, composed of three panes and, in between, two layers of thermo-expanding gel. The glass pane is held in place by means of ceramic fiber gaskets having thickness of 2 mm and width of 20 mm and with glass retaining frames composed of steel profiles having thickness of 1.5 mm fixed by means of screws 4.2x16 and pitch 126.5 mm. The leaf is composed of steel sheet 0.8 mm thick on both sides with a U steel profile having dimensions of 20x36.4x1.5 mm on the edge. Three longitudinal stiffeners, having dimensions of 50x20x1.5 mm and pitch 250 mm, together with insulating material type PAROC 40 mm thick and density of 150 kg/m3 are fitted inside the leaf. The secondary leaf is fitted with two latches, having diameter of 8 mm, one on the top and the other on the bottom The door frame is composed of hollow steel profiles 1.5 mm thick, fitted by means of screws 4.2x25 and pitch 520 mm, to the bulkhead.
Field of application
Fire resistant B-15 Class double leaf hinged door for general application.
In case of doors in compliance to the "Agreement between the European Community and the United States of America", the present certificate is valid at the following conditions:
- doors without windows or with total window area no more than 645 cm2 in each door leaf
- maximum door size tested
- door used with a fire tested frame design
Reference documents
BLU BUD drawing No. B15DHB2 dated 5 March 2015 approved on 20 March 2015 with endorsement No. LABS-1034.
Tests carried out
Test as per RINA Test Laboratory report No. 2015CS01663/1 issued on 19 March 2015 according to Appendix 1 of IMO 2010 FTPC Part 3.




ATTACHMENT TO
CERTIFICATE No. MED188325CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****