MED020123CSENGF- -  -  N- DECORAZIONE TRIDIMENSIONALE CON TECNOLOGIA DIP-PRINT -N- S- S- -27/02/2023- Marine Equipment- - NN- S- - N-  - 723,206B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità- MED020123CS- N-Feb 26, 2028723206
 
Form
  Marine Equipment(TO)
MED059523MI/001,MED033725MI/001
Certification N. MED020123CS - (ENG)
Certificate date 27/02/2023
Type Protezione antincendio
Product Surface materials and floor coverings with low flame-spread characteristics: (b) paint systems
Item Nº MED/3.18b
USCG Category N° 164.112

Model or Denomin.
Items
DECORAZIONE TRIDIMENSIONALE CON TECNOLOGIA DIP-PRINT
Applicant BY BARRET RADICA S.R.L.
Place of requester LOC. CALVAROLA, 10  %  24069 Trescore Balneario (BG)  % ITALY
Tel. N.,Fax, Email +39 035 4258081, 035-4257518, INFO@BARRET.IT
Directive (EU) 2022/1157
Standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference Documents Chap. II-2 and X of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 26/01/2023
Expire date 26/02/2028
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED020123CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2022/1157.
MED Item Nº MED/3.18b
USCG Category Nº 164.112
Description Surface materials and floor coverings with low flame-spread characteristics: (b) paint systems
Type DECORAZIONE TRIDIMENSIONALE CON TECNOLOGIA DIP-PRINT
Applicant BY BARRET RADICA S.R.L.
LOC. CALVAROLA, 10,24069 Trescore Balneario (BG),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference standards Chap. II-2 and X of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
February 27, 2023
February 26, 2028
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED020123CS
Page 1 of 2

Product description


Painting system composed of 3 layers:
1st layer: primer called “ICROEPOX PRIMER 2k” produced by Icro Coatings S.p.A. (mass per area 50 g/m² ± 15%, thickness 0.035 mm ± 20%);
2nd layer: film with various effects called “DIP PRINT” produced by Pozzi Arosio (mass per area 5 g/m² ± 15%, thickness 0.0045 mm ± 20%);
3rd layer: finish called “OPACRYL AR OP 15” produced by IVM Chemicals Srl (mass per area 60 g/m² ± 15%, thickness 0.055 mm ± 20%).
  • Mass per area (g/m²): 115 (± 15%)
  • Thickness (mm): 0.0945 (± 20%)

  • Field of application

    As finishing material for all exposed interior and concealed or inaccessible surfaces (paint system).

    The product may be applied to any metallic support having a thickness ³ 0.90 mm.

    When intended for decks the product may be applied to any metallic support, any non-combustible support and any material having low flame spread characteristics.

    On the basis of the value of the total heat release (Qt) and on the basis of the value of the peak heat release (qp) the material is deemed not generating excessive quantities of smoke nor toxic products in fire according to Annex 2 IMO 2010 FTP Code.

    Tests carried out

    Tests as per RINA Test Laboratory reports No. 2023CS01201/1 and No. 2023CS01201/2 dated 27 February 2023 issued according to:
    • IMO 2010 FTP Code Part 5
    • ISO 1716: 2010




ATTACHMENT TO
CERTIFICATE No. MED020123CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****