MED049026CSENGB- -  -  N- MARINE SHELL NCP/GRP -N- S- S- -04/03/2026- Marine Equipment- - SN- S- - N-  - 602,754B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED049026CS- N-Mar 3, 2031602754
 
Form
  Marine Equipment(TO)
MED049026CS
Certification N. MED049026CS - (ENG)
Certificate date 04/03/2026
Type Protezione antincendio
Product Penetrations through "A" Class divisions: (b) pipe, duct, trunk, etc. penetrations
Item Nº MED/3.26b
USCG Category N° 164.138

Model or Denomin.
Items
MARINE SHELL NCP/GRP
Applicant BIFIRE S.P.A.
Place of requester VIA LAVORATORI DELL'AUTOBIANCHI, 1  %  20832 Desio (MB)  % ITALY
Tel. N.,Fax, Email 0362 364570, ---, ravelli@bifire.it
Directive (EU) 2025/1533
Standards IMO Res. MSC.307(88)-(2010 FTP Code) as amended - IMO MSC.1/Circ. 1488
Reference Documents SOLAS 74 Reg.II-2/9, IMO Res. MSC.1/Circ.1276 Rev.1, IMO Res. MSC.1/Circ.1655.
Request 19/01/2026
Expire date 03/03/2031
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED049026CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2025/1533.
MED Item Nº MED/3.26b
USCG Category Nº 164.138
Description Penetrations through "A" Class divisions: (b) pipe, duct, trunk, etc. penetrations
Type MARINE SHELL NCP/GRP
Applicant BIFIRE S.P.A.
VIA LAVORATORI DELL'AUTOBIANCHI, 1,20832 Desio (MB),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code) as amended - IMO MSC.1/Circ. 1488
Reference standards SOLAS 74 Reg.II-2/9, IMO Res. MSC.1/Circ.1276 Rev.1, IMO Res. MSC.1/Circ.1655.
Issued in Genoa on
This Certificate is valid until
March 4, 2026
March 3, 2031
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED049026CS
Page 1 of 2

Product description


Pipe penetration installed in a bulkhead, having a sheet cutting dimension of diameter 40 mm. The penetration consists of one 0.6 mm carbon steel shell having external diameter of 45.2 mm and a carbon steel flange thickness 5 mm and diameter of 104 mm, tack welded to the bulkhead, by wide stitch welds having 20 mm length, corresponding to the connection between the two half flanges and one for each threaded fixing tab of the collar. The steel shell extends for a length of 50 mm. Inside the shell are provided No. 2 intumescent layers type Seal Bifire S having thickness of 2 mm and width of 50 mm. On the side opposite the penetration, a Bifire mastic sealant bead is provided between the pipe and the sheet metal cut of the bulkhead.
In the bulkhead penetration named MARINE SHELL NCP/GRP25-32 may be installed a 28 mm diameter carbon steel conduit for flexible remote mechanical valve control with torque rotating movement, ARGOMETER series AV/02.
Field of application

Fire resistant A-0 Class metal pipe penetration through bulkhead for general application.
Reference documents

BIFIRE drawing No. BIFIRE-BLKH-A60-001 Rev. B dated on 3 March 2026 (15 sheets, opening "A" and "F") attached to RINA Test Laboratory Report No. 2026CS01490 issued on 3 March 2026 according to Appendix 1 of IMO 2010 FTPC Part 3.
Tests carried out

Test as per RINA Test Laboratory Report No. 2026CS01490 issued on 3 March 2026 according to Appendix 1 of IMO 2010 FTPC Part 3.




ATTACHMENT TO
CERTIFICATE No. MED049026CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****