MED369322CS!002ENGB- -  -  N- SITAL F.P.IX.D.D. -N- S- S- -28/11/2022- Marine Equipment- - SN- S- - N-  - 62,219B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità- MED369322CS/002- N-Oct 18, 202762219
 
Form
  Marine Equipment(TO)
MED369322CS/002
Certification N. MED369322CS/002 - (ENG)
Certificate date 28/11/2022
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model or Denomin.
Items
SITAL F.P.IX.D.D.
Applicant SITAL S.R.L
Place of requester VIA DELL' ARTIGIANATO 1  %  29028 PONTE DELL' OLIO (PC)  % ITALY
Tel. N.,Fax, Email 0523 878421, 0523 875141, ---
Directive (EU) 2022/1157
Standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference Documents Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 14/09/2022
Expire date 18/10/2027
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED369322CS/002

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2022/1157.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type SITAL F.P.IX.D.D.
Applicant SITAL S.R.L
VIA DELL' ARTIGIANATO 1,29028 PONTE DELL' OLIO (PC),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference standards Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
November 28, 2022
October 18, 2027
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED369322CS/002
Page 1 of 2

Product description

Double leaf hinged door with maximum clear opening size of 1965 mm (W) and 2356 mm (H). The door leaf, having maximum dimensions of 1025 (W) x 2450 (H) mm and thickness of 65 mm, is composed of two stainless steel sheets 2 mm thick each and, between, an insulating material compound. The insulation material compound is composed of a layer of material type GIPSBIFIRE, 15 mm thick and having density of 880 kg/m3 fitted between two layers of mineral wool type PAROC MARINE SLAB 180 having, each, density 180 kg/m3 and nominal thickness 25 mm (compressed). The leaf is fitted, inside, with No. 16 transversal stainless steel stiffeners having dimensions of 15x15x2 mm; eight stiffeners are welded, with pitch of 320 mm, to one sheet and eight to the opposite sheet. The door frame is composed of a stainless steel Z shaped profile, 4 mm thick, bolted to the bulkhead with bolts M10 fitted with pitch of 300 mm. Gaskets type PAPERSEAL ECO, having thickness of 3 mm, are inserted between frame and bulkhead. The secondary leaf is equipped with a lever closing device, that acts on 2 points, actuated by an handle; the primary leaf is equipped with a lever closing device, that acts on 3 points, actuated by an handle and a panic bar.

Field of application
Fire resistant A-60 Class double leaf hinged door.
Reference documents
Sital Srl drawing No. 42-6369 dated 25 September 2012 approved on 12 October 2012 with endorsement No. LABS-718.
Tests carried out
Test as per RINA Test Laboratory Report No. 2012CS012876/2 issued on 18 October 2012 according to IMO Res. A. 754(18).




ATTACHMENT TO
CERTIFICATE No. MED369322CS/002
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****