MED390424CS!002ENGD- -  -  N- Anti-splashing AGFA3020 -N- S- S- -14/10/2024- Marine Equipment- - SN- S- - N-  - 2,327,838B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED390424CS/002- N-Oct 13, 20292327838
 
Form
  Marine Equipment(TO)
MED425924WS/002
Certification N. MED390424CS/002 - (ENG)
Certificate date 14/10/2024
Type Protezione antincendio
Product Surface materials and floor coverings with low flame-spread characteristics: (a) decorative veneers
Item Nº MED/3.18a
USCG Category N° 164.112

Model or Denomin.
Items
Anti-splashing AGFA3020
Applicant Anhui Zhongxue Adhesive Tape MFG Co., Ltd.
Place of requester No. 26 Liming Road, Lai'an Economic Development Zone  %  239200 Chuzhou (Anhui)  % CHINA
Tel. N.,Fax, Email ---, ---, ---
Directive (EU) 2024/1975
Standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference Documents Chap. II-2 and X of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 16/08/2024
Expire date 13/10/2029
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED390424CS/002

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2024/1975.
MED Item Nº MED/3.18a
USCG Category Nº 164.112
Description Surface materials and floor coverings with low flame-spread characteristics: (a) decorative veneers
Type Anti-splashing AGFA3020
Applicant Anhui Zhongxue Adhesive Tape MFG Co., Ltd.
No. 26 Liming Road, Lai'an Economic Development Zone,239200 Chuzhou (Anhui),CHINA
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference standards Chap. II-2 and X of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
October 14, 2024
October 13, 2029
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED390424CS/002
Page 1 of 2


Product description

Fire retardant tape composed of aluminium foil (0.03 mm thick), composite adhesive (0.01 mm thick), fiberglass cloth (0.14 mm thick), composite adhesive (0.01 mm thick), aluminium foil (0.03 mm thick), acrylic glue (0.045 mm thick), release film (0.035 mm thick).
  • Total mass per area (g/m2): 500 ± 50
  • Total thickness (mm): 0.3 ± 0.02


Fields of application

As finishing material for all exposed interior and concealed or inaccessible surfaces (decorative veneer).

The product may be applied to any non-combustible (non metallic) support having a thickness ³ 25 mm and a density ³ 712.5 kg/m3.

On the basis of the value of the total heat release (Qt) and on the basis of the value of the peak heat release (qp) the material is deemed not generating excessive quantities of smoke nor toxic products in fire according to Annex 2 IMO 2010 FTP Code.
On the basis of the values above the material is exempted from testing in accordance to standard ISO 1716. It will be expected to satisfy a requirement of maximum gross calorific value (e.g., 45 MJ/m2) without further testing.

The product has also been subjected to test according to procedure Q/320115 ZXJ 001-2022 “Pressure sensitive adhesive tape”.

Tests carried out

Tests as per Far East Fire Testing Centre (FEFTC) Test Laboratory report No. FT24231 dated 11 June 2024 issued according to:
  • IMO 2010 FTP Code Part 5.


Tests as per Nanjing Institute of Product Quality Supervision & Testing reports Nos. NZJ(2024)RY01-03560Z and NZJ(2024)RY01-03561Z dated 27 August 2024.




ATTACHMENT TO
CERTIFICATE No. MED390424CS/002
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****