MED072624CSENGF- -  -  N- ALOSA -N- S- S- -07/03/2024- Marine Equipment- - SN- S- - N-  - 457,713B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED072624CS- N-Mar 6, 2029457713
 
Form
  Marine Equipment(TO)
MED051324GE/002,MED051324GE/004,MED051324GE/008,MED042125GE/001,MED042125GE/007,
MED042125GE/008,MED042125GE/009,MED040126GE/001,MED040126GE/002,MED053626GE/001,
MED040126GE/003,MED040126GE/007,MED040126GE/008,MED040126GE/009,MED040126GE/011,
MED040126GE/012,MED040126GE/010,MED040126GE/013
Certification N. MED072624CS - (ENG)
Certificate date 07/03/2024
Type Apparecchi di navigazione
Product Pilot ladder
Item Nº MED/4.49
USCG Category N° 163.003

Model or Denomin.
Items
ALOSA
Applicant F.LLI SANGIACOMO S.N.C. DI SANGIACOMO LORENZO & C.
Place of requester LOCALITA' PRODONNO 25  %  16017 Isola Del Cantone (GE)  % ITALY
Tel. N.,Fax, Email 010 9636133, 010 9636133, ---
Directive (EU) 2023/1667
Standards IMO Res.A.1045(27), as amended,ISO 799-1:2019.
Reference Documents SOLAS 74 Reg. V/23, IMO Res. A.1045(27), IMO MSC/Circ.1428.
Request 28/02/2024
Expire date 06/03/2029
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Davide Campora S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED072624CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Navigation Equipment requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2023/1667.
MED Item Nº MED/4.49
USCG Category Nº 163.003
Description Pilot ladder
Type ALOSA
Applicant F.LLI SANGIACOMO S.N.C. DI SANGIACOMO LORENZO & C.
LOCALITA' PRODONNO 25,16017 Isola Del Cantone (GE),ITALY
Testing standards IMO Res.A.1045(27), as amended,ISO 799-1:2019.
Reference standards SOLAS 74 Reg. V/23, IMO Res. A.1045(27), IMO MSC/Circ.1428.
Issued in Genoa on
This Certificate is valid until
March 7, 2024
March 6, 2029
This Certificate consists of this sheet plus an attachment

________________________________________
Giovanni Carratino
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED072624CS
Page 1 of 2

Product description


Pilot ladder with the following main components:
Bridge wood step: Lenght: (525 ± 2)mm - Breadth: (115±2) mm - Height : (57±2) mm, n° 4 holes Ø25 (±1) mm;
Flat wood step: Lenght: (525±2) mm - Breadth: (115±2) mm - Height: (28±1) mm, n° 4 holes Ø25 (±1) mm;
Spreader wood step: Lenght: (1800±2) mm - Breadth: (115±2) mm - Height: (28±1) mm, n° 4 holes Ø25 (±1)mm
Rubber step: Lenght: (535 ± 2) mm - Breadth: (115±2) mm - Height : (77±2) mm, n° 4 holes Ø25 (±1) mm;
Side rope according to ISO1181:2004. Diameter 20 mm - Minimum breaking strenghth: 24kN.
Reference document
Pilot ladder drawing issued by F.lli Sangiacomo and approved by RINA with n° CSST 22328;
Datasheet material anc components filed by RINA with n° CSST22329.

Tests carried out
Test reports n° 2024/CS/01/726/RSA issued and filed by RINA with n° CSST 22330.

Remarks

The bottom of at least two step of the ladder shall be marked as per ISO 799-1:2019 Par 8.1.
The bottom of each replacement step shall be marked as per ISO 799-1:2019 Par 8.2.
A ladder shall not include more than two replacement steps and one replacement spreader step.
A permanent marking should be provided at regular intervals (e.g. 1 m) throughout the length of the ladder consistent with ladder design, use and maintenance in order to facilitate the rigging of the ladder to the required height.

This certificate supersides and replaces certificate MED293123CS issued on August 4, 2023.




ATTACHMENT TO
CERTIFICATE No. MED072624CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Giovanni Carratino
**** NOTICE: This is NOT an official certificate ****