MED016225CS!003ENGB- -  -  N- B-15 Partition Wall Panel -N- S- S- -17/01/2025- Marine Equipment- - SN- S- - N-  - 1,083,701B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED016225CS/003- N-Jan 16, 20301083701
 
Form
  Marine Equipment(TO)
MED016225CS/003
Certification N. MED016225CS/003 - (ENG)
Certificate date 17/01/2025
Type Protezione antincendio
Product 'A' and 'B' Class divisions fire integrity: (b) 'B' Class divisions
Item Nº MED/3.11b
USCG Category N° 164.108

Model or Denomin.
Items
B-15 Partition Wall Panel
Applicant MERCAN PANEL URETIM SAN. VE TIC. A.S.
Place of requester ÇERKESLI OSB MAH., IMES BULVARI, No.11 DILOVASI, KOCAELI Kocaeli  % TÜRKIYE
Tel. N.,Fax, Email +90 262 502 0180, +90 262 502 0182, yasinyamac@mercanpanel.com
Directive (EU) 2024/1975
Standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference Documents IMO Circ. MSC.1 1120,SOLAS 74 Reg. II-2/9,SOLAS 74 Reg. II-2/3.4,IMO Circ. MSC.1 1581
Request 17/12/2024
Expire date 16/01/2030
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED016225CS/003

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2024/1975.
MED Item Nº MED/3.11b
USCG Category Nº 164.108
Description 'A' and 'B' Class divisions fire integrity: (b) 'B' Class divisions
Type B-15 Partition Wall Panel
Applicant MERCAN PANEL URETIM SAN. VE TIC. A.S.
ÇERKESLI OSB MAH., IMES BULVARI, No.11 DILOVASI, KOCAELI Kocaeli,TÜRKIYE
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference standards IMO Circ. MSC.1 1120; SOLAS 74 Reg. II-2/9; SOLAS 74 Reg. II-2/3.4; IMO Circ. MSC.1 1581
Issued in Genoa on
This Certificate is valid until
January 17, 2025
January 16, 2030
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED016225CS/003
Page 1 of 2

Product description

Bulkhead having maximum dimension 1685 mm width, 2910 mm height and thick of 50 mm. Bulkhead composed of two side by side bulkheads installed with, in between, a minimum air gap of 100 mm. Each bulkheads, consisting of maximum three panels having maximum width of 540 mm and maximum height of 2910 mm; the panels are composed of two steel sheets, having thickness of 0.6 mm each and with inside one layer of mineral wool Izocam Marine Firebattes 140 recognized as not combustible material as per FTP Code 2010. The mineral wool is glued to the steel sheets by means of 250 g/m2 of glue named Sika Force 710 L100. The panel joints, on the exposed side, consist of two “C”shaped steel clips profiles, up and down, having dimensions of 10x8x10 mm and thickness of 0.6 mm. The bulkhead is fitted on the upper side with a "U" shaped steel profile with a thickness of 1.2 mm and dimensions of 50x25 mm and on the bottom with a “U” shaped steel profile with a thickness of 1.2 mm having dimensions of 50x25 mm and on the side with a "U" shaped steel profile with a thickness of 0.6 mm having dimensions of 50x25 mm. The panels, on the exposed side, are fixed by means of screws having diametre of 4 mm, on fixin installation profile having pitch horizontally 200 mm and vertically 300 mm.

Field of application
Fire resistant B-15 Class bulkhead for general application.

Due to the fact that this B class bulkhead has been tested from only one side and has been designed to be installed with the untested side adjacent to the untested side of another B class bulkhead, this EC type-examination certificate is valid only if these conditions are respected when installed on board ensuring that the level of protection indicated in the relevant fire integrity tables included in SOLAS Chapter II-2/Reg.9.2 Thermal and Structural Boundaries is always fulfilled.

Reference documents
Mercan Panel drawing No. MRN-WP-M2 dated 29/01/2024 enclosed on the test report No. RFTR24043-REV1 issued on 06/11/2024, and Mercan Panel drawing No. MRN-WP-M2 rev. 0 dated 16/01/2025 identified by No. 2025CS01162/1.

Tests carried out
Tests as per Efectis Laboratory test report No. RFTR24043-REV1 issued on 06/11/2024 according to IMO Res. MSC.307(88)-(2010 FTP Code), as amended.




ATTACHMENT TO
CERTIFICATE No. MED016225CS/003
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****