MED390624CS!002ENGB- -  -  N- Window A0 - Double glass -N- S- S- -11/12/2024- Marine Equipment- - SN- S- - N-  - 194,862B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED390624CS/002- N-Dec 10, 2029194862
 
Form
  Marine Equipment(TO)
MED390624CS/002
Certification N. MED390624CS/002 - (ENG)
Certificate date 11/12/2024
Type Protezione antincendio
Product 'A' & 'B' class fire proof windows and side scuttles
Item Nº MED/3.25

Model or Denomin.
Items
Window A0 - Double glass
Applicant HET ANKER BV
Place of requester KAATSBAAN 10  %  4209 Schelluinen  % NETHERLANDS
Tel. N.,Fax, Email +31183623135, ---, truus@anker-windows.com
Directive (EU) 2024/1975
Standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference Documents SOLAS 74 Reg. II-2/9,IMO Res. MSC.5(48)-(IGC Code) 3,IMO MSC/Circ.1120
Request 03/09/2024
Expire date 10/12/2029
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED390624CS/002

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2024/1975.
MED Item Nº MED/3.25
Description 'A' & 'B' class fire proof windows and side scuttles
Type Window A0 - Double glass
Applicant HET ANKER BV
KAATSBAAN 10,4209 Schelluinen,NETHERLANDS
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference standards SOLAS 74 Reg. II-2/9; IMO Res. MSC.5(48)-(IGC Code) 3; IMO MSC/Circ.1120
Issued in Genoa on
This Certificate is valid until
December 11, 2024
December 10, 2029
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED390624CS/002
Page 1 of 2

Product description

Window having maximum clear size of 1500 mm x 1500 mm (WxH). The glass compound, moving from the exposed side, is composed of a toughened pane having thickness of 12 mm (manufacturer Veneto Vetro), a cavity 35 mm deep and a toughened pane having thickness of 12 mm (manufacturer Veneto Vetro). The frame is composed of a steel profile having depth of 120 mm, welded to the bulkhead on both sides. The glass retaining frame, fitted on the side exposed to the fire and composed of a stainless steel flat having width of 35 mm and thickness of 8 mm, is fixed to the frame by means of M6 screws fitted with pitch of 50 mm. Between the glass faces, the frame and the glass retaining frame, ceramics gaskets, 2 mm thick, are fitted. Between the glass edge and the frame, on the lower side, spacers of calcium silicate type PROMATECT H, having thickness of 4 mm, are fitted. The glass panes are sealed by means of silicone type BOSTIK MSR_CA.
The window may also be produced by Naval Suppliers Srl - Zona Industriale 24 - 33049 San Pietro al Natisone (UD) - Italy.

Field of application
Fire resistant A-0 Class window with fire hazard in the inner side of the application.

Reference documents
HET ANKER BV drawing No. FTW-A0-SQ1-1616-12-A35-12 dated 25 November 2014 approved on 1 December 2014 with endorsement No. LABS-996.
Tests carried out
Tests as per RINA Test Laboratory Laboratory report No. 2014CS013474 issued on 1 December 2014 according to IMO 2010 FTP Code Part. 3 Appendix 2 - A.I - Windows.




ATTACHMENT TO
CERTIFICATE No. MED390624CS/002
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****