MED500226CSENGB- -  -  N- HB-HH-F -N- S- S- -30/09/2026- Marine Equipment- - SN- S- - N-  - 2,394,348B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED500226CS- N-Sep 29, 20312394348
 
Form
  Marine Equipment(TO)
MED500226CS
Certification N. MED500226CS - (ENG)
Certificate date 30/09/2026
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model
Items/Sizes
HB-HH-F
Applicant BAGGEROD A.S.
Place of requester Nedrevei 8, Building 30D  %  3183 Horten  % NORWAY
Tel. N.,Fax, Email +4745617869, ---, aan@baggerod.no
Directive (EU) 2026/1434
Standard IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ.1319
Reference Documents SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511/Revision 1
Request 07/09/2026
Validity 29/09/2031
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED500226CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2026/1434.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type HB-HH-F
Applicant BAGGEROD A.S.
Nedrevei 8, Building 30D,3183 Horten,NORWAY
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ.1319
Reference standards SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511/Revision 1
Issued in Genoa on
This Certificate is valid until
September 30, 2026
September 29, 2031
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED500226CS
Page 1 of 2

Product description

Double leaf hinged door whose maximum clear opening size is 1985 mm wide and 2100 mm high. The door leaves, having maximum width of 931 mm (primary leaf) and 1085 mm (secondary leaf), maximum height of 2116 mm and thickness of 64 mm, are composed of two stainless steel sheets, 2 mm thick each and, in between, a layer of insulating material type FireMaster Marine Plus blanket having thickness of 60 mm and density of 128 kg/m3. Each leaf is fitted with two L shaped steel stiffeners, 2 mm thick and having dimensions of 20x40 mm tack welded, with pitch of 150 mm, to the sheet opposite to the hinges. The secondary leaf is equipped, on the upper and lower part, with two latches which fix the leaf to the frame and to the sill; the sill is composed of a stainless steel flat, 3 mm thick and having width of 90 mm. The door frame is composed of an L shaped steel profile, having thickness of 3 mm and dimensions of 60x90 mm, bolted to the bulkhead by means of M8 bolts, fitted with pitch of 300 mm. The secondary leaf may be fitted with drop down gasket. The primary leaf may be fitted with a self closing hose port having maximum clear opening size of 150x150 mm.

The product may be also manufactured by:
Baggerød AS - Nevredei 8, Building 30D, 3183 Horten (Norway).
Field of application
Fire resistant A-60 Class double leaf hinged door for general application. Fire resistant A-30 Class double leaf hinged door in compliance with IMO MSC.1/Circ. 1319 dated 11 June 2009. In this case the dimensions relevant to the height and with of the door may be increased of 15% provided that the surface area is not increased of more than 10%.

In case of doors in compliance to the "Agreement between the European Community and the United States of America", the present certificate is valid at the following conditions:
- maximum door size tested;
- door used with a fire tested frame design.

The surfaces of this division may be fitted with products having low flame spread characteristics, installed as described in the relevant type approval certificates and satisfying the requirements of SOLAS 74 Reg. II-2 as applicable.
Reference documents
BAGGERØD drawing No. 20918-001 dated 12 September 2016 approved on 26 October 2016 with endorsement No. LABS- 1358.
Tests carried out
Tests as per RINA Test Laboratory Report No. 2016CS013022 issued on 26 October 2016 according to IMO 2010 FTP Code Part 3 and to IMO MSC.1/Circ. 1319 dated 11 June 2009.




ATTACHMENT TO
CERTIFICATE No. MED500226CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****