MED366924WSENGD- -  -  N- CYFE Series -N- S- S- -28/06/2024- Marine Equipment- - SN- S- - N-  - 147,930B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED366924WS- N-Jun 27, 2029147930
 
Form
  Marine Equipment(TO)
MED345824WS/002
Certification N. MED366924WS - (ENG)
Certificate date 28/06/2024
Type Prevenzione dell'inquinamento marino
Product Oil-filtering equipment (for an oil content of the effluent not exceeding 15 p.p.m.)
Item Nº MED/2.1

Model or Denomin.
Items
CYFE Series
Applicant Shanghai Shijiu Marine Equipment Co., Ltd.
Place of requester No. 600 Minsheng Road, Pudong  %  200134 Shanghai  % CHINA
Tel. N.,Fax, Email +86 21 58854164, ---, jiyi@shijiumarine.com
Directive (EU) 2023/1667
Standards IMO Res. MEPC.107(49), as amended,IMO MEPC.1/Circ.643
Reference Documents MARPOL 73/78 Annex I, Reg.14, IMO MEPC.1/Circ.643.
Expire date 27/06/2029
Responsible Office SHANGHAI
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Qiang Sun S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED366924WS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Marine-Pollution prevention requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2023/1667.
MED Item Nº MED/2.1
Description Oil-filtering equipment (for an oil content of the effluent not exceeding 15 p.p.m.)
Type CYFE Series
Applicant Shanghai Shijiu Marine Equipment Co., Ltd.
No. 600 Minsheng Road, Pudong,200134 Shanghai,CHINA
Testing standards IMO Res. MEPC.107(49), as amended,IMO MEPC.1/Circ.643
Reference standards MARPOL 73/78 Annex I, Reg.14, IMO MEPC.1/Circ.643.
Issued in SHANGHAI on
This Certificate is valid until
June 28, 2024
June 27, 2029
This Certificate consists of this sheet plus an attachment

________________________________________
Qiang Sun
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED366924WS
Page 1 of 3
Product description

The equipment is intended for installation onboard ships to reduce oil content in bilge water to less than 15ppm.

The equipment is designed and tested to meet the requirements of the IMO Resolution MEPC.107(49), as amended and IMO MEPC.1/Circ.643.



Application/Limitation
15ppm Bilge Separators,Models:

Type
Capacity (m3/h)
Maximum working pressure(Mpa)
CYFE-0.1
0.1
0.2
CYFE-0.25
0.25
0.2
CYFE-0.5
0.5
0.2
CYFE-1
1
0.2
CYFE-2
2
0.2
CYFE-3
3
0.2
CYFE-5
5
0.2

Reference documents/principle system drawings

Installation dimensions drawing - CYFE-0.1-00/0.25-00/0.5-00/1-00/2-00/3-00/5-00


Instruction book(manual)
CYFE series device control box diagram - CYFE-K-01/02/03/04
Control system diagram - CYFE-D-02-1
Electrical principle diagram - CYFE-D-01-01/02/03





ATTACHMENT TO
CERTIFICATE No. MED366924WS
Page 2 of 3


Tests carried out

Environmental test - No.704 Research Institute of China Shipbuilding Industry Corporation


-Vibration test - Report No.S190-ZD-2015

-High temperature test - Report No.S043-GW-2014

-Low temperature test - Report No.S043-DW-2014

-Humidity test - Report No.S043-SR-2014

-Inclination test - Report No.S043-QY-2014

Determination of oil content test - Shanghai Environmental Monitoring Centre


-Report No.WS15020


Marking of product

For traceability to this type approval,each unit is to be marked with:


-Manufacturers name of trade mark

-Type designation

-Capacity

-Serial No.

This certificate annuls and replaces previous issued certificate No. MED124220WS/001.





ATTACHMENT TO
CERTIFICATE No. MED366924WS
Pages 3 of 3
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Qiang Sun
**** NOTICE: This is NOT an official certificate ****